Hazards Management Plan
This section has been reviewed and updated as needed: May 2014
A Hazards Management Plan (HMP) is a written safety and environmental plan for a work unit, which provides a framework for ensuring compliance with regulations pertaining to protection of personnel and the environment. The primary purposes of the HMP are to provide safety information for employee in each work unit, to provide documentation of compliance with occupational and environmental regulations, and to provide information to UNC-CH Department of Environment, Health and Safety (EHS) for use in determining job specific training requirements.
Environment, Health and Safety
EHS is responsible for reviewing the submitted HMPs, inspecting work locations, and ensuring compliance with the regulations.
The supervisor is responsible for developing an HMP, communicating its contents to his/her employees, maintaining safety/environmental compliance, and sending a copy to EHS.
Instructions for Preparing a Hazards Management Plan (HMP)
The HMP has nine essential elements and each of these are addressed in a different section of the plan. Each section provides information to EHS on the personnel within the work unit and the nature of the unit’s operation. The HMP is to be updated on an annual basis or if there is a change within the work unit (i.e. change in location and/or change in tasks). The following instructions provide information on how to complete each section of the plan:
1. Work Unit Data
This section provides information to EHS on the work unit location, supervisor, and after hours phone number in the event of an emergency. EHS generates a work unit number by using the department and/or shop number to designate smaller work groups within a department.
This section identifies each employee in the work unit along with their University Personal Identification (PID) number (the 9 digit number under the picture of the individual’s UNC One Card). EHS will take this information and enter it into a database. Once a work unit is established in the EHS database system, the work unit needs only to verify that the information is correct or make modifications during annual HMP updates.
3. Hazardous Materials Inventory
List all hazardous materials used or stored by employees in the work unit, including the manufacturer’s name. (ex. Paint, oil, aerosol spray cans, compressed gas, etc.)List the size of the container in grams, liters, pints, quarts, or gallons and then list the number of items of that quantity in parenthesis.Safety Data Sheet (SDS) – A notebook that contains current copies of SDSs of materials being used or stored must be maintained and be readily accessible to all employees within the work unit. An SDS document must be on hand for every chemical that is used in the shop.
Tips for keeping your SDS book in order:
- A list of the chemicals located in the shop area should be inserted at the front of the notebook for anyone to be able to easily access/find a SDS form.
- The SDS book must be prepared in an orderly fashion so that anyone can easily locate a specific SDS form in the event of an emergency. (Preferably in alphabetical order.)
- New chemicals that are being used in the shop should have an SDS available to employees immediately.
- Old SDS forms should be updated, and SDS forms of chemicals that are no longer used should be taken out of the current SDS book and placed into a file.
Locations – List the rooms or work areas (including trucks) where materials are stored when they are not being used.
Compatibility Group identifies the chemical’s characteristic designation:
- A: acids
- B: bases
- C: organics not listed in other groups
- D: flammable/combustible liquids
- E: inorganic oxidizers and heavy metals
- F: organic peroxides
- G: water and air reactives
- H: cyanides and sulfides
- I: highly toxic chemical
- J: compressed gasses
- K: aerosol cans
**The work unit can leave the Compatibility Group blank if they are not familiar with a chemical’s designation.The RCRA Code section is for EHS to complete. This section specifies the hazardous waste code.
Disposal Methods indicates how waste is managed or disposed of in the shop.
- T: trash
- L: commercial laundry
- R: recycled
- H: picked up by EHS
4. Hazardous Equipment
List the name and manufacturer of powered equipment used or stored by your work unit.List the number of pieces of equipment.Indicate the type of power: E-3 for electrical with ground wire, E-DI for double insulated electrical equipment, or P for pneumatic powered equipment. List the type if other than E or P.
Indicate whether the equipment is fixed or portable.
List the designated users of the equipment.
5. Identification of Required Safety Training
Check the applicable training for the employees within your work unit. If some training is only required for one employee or a select few, the complete a separate form for each individual or group. These forms are required to be turned in to EHS so that employees can be identified as needing specific types of training.
6. Personal Protective Equipment (PPE) Hazard Assessment
Review the operations within the work unit and then indicate whether there is a hazard that requires the use of PPE. Call EHS if you need help in deciding what PPE your specific type of work requires.
7. Job Safety Analysis (JSA)
JSAs are to be completed for the following operations:
- The most hazardous task.
- Least frequent task
- If an on-the-job injury has occurred in the performance of this task.
**All JSAs are to be sent to EHS for review, and for EHS to decide if the JSA warrants further study and analysis. Once it has been reviewed, the JSA will then be listed under the online JSA Library.
8. Environmental Issues and Hazardous Waste Management
The questions in this section are designed to gather information on your work unit’s current waste management practices. The work unit is to describe how wastes from each operation are handled, including empty containers, leftover material (paint, aerosol cans and contaminated items (rags).). This information will be used to tailor waste management programs and training to meet the needs of each work unit.
9. Respirator Section
This section must be completed if employees wear respirators or have been assigned respirators. Describe how the respirators are used, types of respirators used, and which employees use respirators. Completion of this section will aid in management of the work unit’s respiratory protection program.